description

Heat-reflecting substrate E-PEX (depending on the batch, the inscription on the E-pex thermal lining can be Heat Plus or DH HILon) was developed by engineers Seggi Century Plant - for the production of warm film floor Heat Plus leader, especially for installation under floor heating film, in order to heat and waterproofing for lightweight coverings (laminate, parquet, carpet, linoleum, etc. ).

This substrate is significantly better technology for use in warm floors than standard substrate under the floating lungs coating as in its structure it is coating laminated Mylar, which serves to teplootrazheniya lower portion of the infrared radiation Hit Plus film, in addition to insulating properties and gidrobarernym.

The substrate is laid on the entire floor area for a uniform height of the floor covering, insulation from the rough floor. The thickness of E-pex is 4 mm, while the minimum shrinkage at constant pressure is 1-1.5 mm. The additional thickness from the use of a substrate under the floor covering is 3-4 mm.

The main features of the heat-reflecting substrate E-pex:

• - High thermal insulation performance.
• - Laminated lavsan thermo-reflective coating.
• - Increased moisture resistance and protection against condensation.
• - Does not conduct an electric current.
• - Environmentally friendly material.
• - It is used for installation under light coatings.

description

E-PEX with grounding, this is a new product in the heat-reflecting substrates of Heat Plus.

Heat-reflecting substrate E-PEX was developed by engineers Seggi Century Plant - for the production of warm film floor Heat Plus leader, especially for installation under floor heating film, in order to heat and waterproofing for lightweight coverings (laminate, parquet, carpet, linoleum, etc. ).

This substrate is significantly better technology for use in warm floors than standard substrate under the floating lungs coating as in its structure it is coating laminated Mylar, which serves to teplootrazheniya lower portion of the infrared radiation Hit Plus film, in addition to insulating properties and gidrobarernym.

The substrate is laid on the entire floor area for a uniform height of the floor covering, insulation from the rough floor. The thickness of E-pex is 4 mm, while the minimum shrinkage at constant pressure is 1-1.5 mm. The additional thickness from the use of a substrate under the floor covering is 3-4 mm.

The main features of the heat-reflecting substrate E-pex:

• - Earthing layer.
• - High thermal insulation performance.
• - Laminated lavsan thermo-reflective coating.
• - Increased moisture resistance and protection against condensation.
• - Does not conduct an electric current.
• - Environmentally friendly material.
• - It is used for installation under light coatings.

description

E-dero - a proprietary grounding layer from TM Heat Plus, is used to protect against static voltage when using heating systems based on infrared film.

The material of flexible polyester with a carbon-coated coating is laid directly on the film and completely absorbs electromagnetic radiation, but unlike foil materials it does not interfere with the passage of infrared radiation.

The removal of static voltage is necessary in rooms with high humidity, metal structures or rooms with increased safety requirements.

E-dero is a roll material that is easily cut and easy to install. When laying a warm floor to the ground plane, connect a common ground wire.

description

Seggi Century engineers developed specially for laying under soft floor coverings a protective heat-spreading layer E-stone made of basalt fiber and polyester.

To date, E-stone is the only, unparalleled material developed specifically for the uniform distribution of heat and protection against mechanical damage to the Heat Plus film floor. Not combustible and not emitting free particles into the air. This material is more effective in terms of heat distribution and mechanical protection, than the currently used fiberboard, GVL, etc.

The material layer is laid on the entire surface of the floor for uniform heat distribution and the same height of the floor covering. The thickness of the sheet is 3 mm, which practically does not affect the general rise of the floor.

The sheets of material are placed on top of the infrared film under the floor covering. For ease of installation, E-stone sheets are marked with cut lines. Between each other the plates are fastened with Heat Plus mounting tape.

The main features of the heat-distributing protective substrate E-stone:

• - Uniform heat distribution over the surface of the floor covering.
• - Protection against local overheating.
• - Protection against mechanical damage to the film.
• - Does not conduct an electric current.
• - Environmentally friendly material.
• - It is used for installation under light coatings.

description

Laminated reinforced aluminum film-heat reflector with an additional protective effect - Strotex 90Al is used for thermal and waterproofing when laying infrared heated floors. Heath Plus for heavy coatings (tiles, marble, etc.).

The substrate is laid under a film for vapor and hydroprotection from evaporation from the screed, as well as to reflect the lower part of the infrared radiation of the film. Thus, the efficiency of the heating system is increased due to the reduction of heat losses to the heating of the concrete screed.

Due to the minimum thickness of the film (0.15 mm), the floor level does not change, which makes it possible to lay the film on the finished screed under the tile without additional costs for leveling the floor. Also, when installing under the tile, adhesive compositions can be used to fix the substrate on the screed and the film on the substrate.

Strotex fits under the film with a margin around the perimeter of 10-15 cm.

description

Thermal insulating substrate Izolon with a heat-reflecting coating is used for laying infrared heating systems for light coatings (laminate, parquet, linoleum, parquet) to create a floating effect, heat reflection of the lower part of the film radiation and thermal insulation from the floor.

Due to the materials used in the preparation of the substrate, Izolon has high steam and waterproofing properties, does not absorb moisture and does not deteriorate from contact with the screed.

The substrate is placed under the infrared film on the entire surface of the room for thermal insulation effect and one level of floor covering. With a thickness of 4 mm, the substrate has a sufficiently strong shrinkage up to 1.5-2 mm, in contrast to the E-pex proprietary substrate, which must be taken into account when installing floor coverings.

description

A glass mesh is used when installing an infrared film under the screed for heavy coatings.

The main function is reinforcement of the filler floor to avoid cracks and deformation of the floor covering.

The grid is laid on top of the pie from insulating materials, infrared film, polyethylene sleeve, with a margin around the perimeter of 10-15 cm.

The mounting grid is fixed with dowels and filled with a screed.

description

The polyethylene hose is used in the process of laying the Heat Plus infrared film under the screed for heavy floor coverings. The main task of polyethylene film is to protect the heating film from the aggressive impact of the screed.

Upon drying, the screed changes its geometric shapes, which can lead to mechanical damage to the infrared film. Using polyethylene as a layer - reduces the risk of damage. In addition, the concrete screed is an alkaline medium, which can also negatively affect the heating element in the system of warm floors.

When stacking the sleeve is cut to the canvas and mounted on top of the film strips, with a margin at the edges of 10-15 cm. Surplus of the film is turned inward, creating an envelope. In this configuration, the Heat Plus film is reliably protected from environmental influences.

Due to the minimum thickness (0.15 mm), polyethylene has virtually no effect on the passage of infrared radiation.